4 Ton 15.2 SEER2 Goodman Heat Pump Split System GSZH504810+AMST48CU1400

<h3>4 Ton 15.2 SEER2 Goodman Heat Pump Split System GSZH504810+AMST48CU1400</h3> <strong>Standard Features</strong> <ul> <li>High-efficiency scroll compressor</li> <li>SmartShift® technology to ensure quiet reliable defrost</li> <li>Copper tube/ enhanced aluminum fin coil- 5mm diameter on 1.5-3.5T</li> <li>Factory-installed suction-line accumulator</li> <li>Factory-installed compressor crankcase heater</li> <li>Factory-installed high-capacity muffler</li> <li>High- and low-pressure switches</li> <li>Service valves with sweat connections and easy access to gauge ports</li> <li>Fully charged for 15’ of tubing length</li> <li>Contactor with lug connection</li> <li>Ground lug connection</li> <li>AHRI Certified; ETL Listed</li> </ul> <strong>Cabinet Features</strong> <ul> <li>Removable grille style top design compliant with UL 60335-2-40</li> <li>Steel louver coil guard</li> <li>Heavy-gauge galvanized-steel cabinet</li> <li>Attractive Architectural Gray powder-paint finish with 500-hour salt-spray approval</li> <li>Top and side maintenance access</li> <li>Single panel access to controls with space provided for field-installed accessories</li> <li>When properly anchored, meets the 2020 Florida Building Code unit integrity requirements for hurricane-type winds (Anchor bracket kits available.)</li> <ul> <li>Tested and rated in accordance with AHRI Standard 210/240</li> <li>Wire size should be determined in accordance with National Electrical Codes; extensive wire runs will require larger wire sizes</li> <li>Must use time-delay fuses or HACR-type circuit breakers of the same size as noted</li> </ul> </ul> <strong>Notes</strong> <ul> <li>Always check the S&amp;R plate for electrical data on the unit being installed.</li> <li>Installer will need to supply ⅞” to 1⅛” adapters for suction line connections.</li> <li>Unit is charged with refrigerant for 15’ of ⅜” liquid line. System charge must be adjusted per Installation Instructions Final Charge Procedure.</li> <li>Installation of these units requires the specified TXV Kit to be installed on the indoor coil. THE SPECIFIED TXV IS DETERMINED BY THE OUTDOOR UNIT NOT THE INDOOR COIL.</li> </ul> <strong>Product Features</strong> <ul> <li>Internal factory-installed thermal expansion valves for cooling and heat pump applications</li> <li>Direct drive, multi-speed ECM blower motor</li> <li>All-aluminum evaporator coil</li> <li>Coil mounting track for quick repositioning</li> <li>Optimized for use with R-410A refrigerant</li> <li>Cabinet air leakage less than 2.0% at 1.0 inch H₂O when tested in accordance with ASHRAE standard 193</li> <li>Cabinet air leakage less than 1.4% at 0.5 inch H₂O when tested in accordance with ASHRAE standard 193</li> <li>AHRI certified; ETL listed</li> <li>Rigid SmartFrame™ cabinet</li> <li>Horizontal or vertical configuration capabilities</li> <li>21” depth for easier attic access</li> <li>DecaBDE-free thermoplastic drain pan with secondary drain connections</li> <li>Screw-less sides and back helps to reduce condensation when installed in humid locations</li> <li>Foil-faced insulation covers the internal casing to reduce cabinet condensation</li> <li>Galvanized, leather grain-embossed finish</li> <li>Glue-less cabinet insulation retention</li> <li>Tool-less filter access</li> <li>Field Installed 3 kW – 25 kW electric heater kits available</li> </ul>